 |
|||
|
|
|||
|
Page Title:
Resistors R5, R9 thru R15, R18 thru R20, and R82 thru R87 |
|
||
| ||||||||||
|
|
 ARMY TM 5-6675-309-14
MARINE CORPS TM 08840A-14/1
9.
Tighten screw (187) and washer (188)
(204) securing resistor R10 (206) to resis-
securing R10 mounting bracket (189) to
tor mounting bracket no. 5 (203) and
resistor mounting plate no. 2 (202); re-
mounting base.
move resistor.
Tighten resistor mounting bracket screw
10.
securing mounting bracket (203) to
7. Tag and unsolder wires from resistor R10
mounting plate (71, figure 8-6, sheet 3).
(206).
Install three screws (193, figure 8-6, sheet
11.
(b) Replacement.
5) and washers (194) securing shroud no.
1.
Discard nut and lockwasher supplied with
3 (191) to mounting plate (71, figure 8-6,
resistor R10 (206).
sheet 3).
2.
Solder wires to resistor R10 (206).
Install screw (185, figure 8-6, sheet 5),
12.
washer (184), spacer (230), washer (227),
Install centering washer (204) and mica
3.
lockwasher (226), nut (225) securing no. 3
washer (205) on lower end of resistor R10.
shroud (191) to resistor mounting bracket
(206).
no. 4 (228).
4.
Install screw (190), washer (192), center-
13.
Install screw (198) and washer (197) se-
ing washer (208), mica washer (207), mica
curing no. 3 shroud (191) to fan mounting
washer (205), and centering washer (204)
bracket (196).
securing resistor R10 to resistor mounting
Install back cover and secure with six
14.
bracket no. 5 (203) and resistor mounting
latches.
plate no. 2 (202).
15.
Place PSTS front panel (51, figure 8-6,
NOTE
sheet 1) in PSTS instrument case (1).
Align mounting holes.
Check that there is no continuity between
conductive materials separated by mica
16.
Install 20 screws (49) and washers (50)
washers to ensure mica washer has not
securing PSTS front panel (51) to PSTS
been damaged during assembly.
instrument case (1).
5. Install three screws (193) and washers
(31)
Resistors R5, R9 thru R15, R18 thru R20, and
(194) securing shroud no. 3 (191) to
R82 thru R87. Remove and replace typical
mounting plate (71, figure 8-6, sheet 3).
resistor R10 (206, figure 8-6, sheet 5) as fol-
lows:
6.
Install screw (185, figure 8-6, sheet 5),
washer (184), spacer (230), washer (227),
(a) Removal.
lockwasher (226), and nut (225) securing
1.
Remove 20 screws (49, figure 8-6, sheet 1)
shroud no. 3 (191) to resistor mounting
and washers (50) securing PSTS front
bracket no. 4 (228).
panel (51) to PSTS instrument case (1).
7.
Install screw (198) and washer (197) se-
Remove PSTS front panel.
curing shroud no. 3 (191) to fan mounting
Loosen six latches securing back cover;
2.
bracket (196).
remove back cover.
Install back cover and secure with six
8.
Remove three screws (193, figure 8-6,
3.
latches.
sheet 5) and washers (194) securing no. 3
shroud (191) to mounting plate (71, figure
9.
Place PSTS front panel (51, figure 8-6,
8-6, sheet 3).
sheet 1) in PSTS instrument case (1).
Align mounting holes.
4.
Remove screw (185, figure 8-6, sheet 5),
washer (184), spacer (230), washer (227),
10.
Install 20 screws (49) and washers (50)
lockwasher (226), and nut (225) securing
securing PSTS front panel (51) to PSTS
no. 3 shroud to resistor mounting bracket
instrument case (1).
no. 4 (228).
(32) Resistors R6 thru R8, R16, and R17. Remove
Remove screw (198) and washer (197)
5.
and replace typical resistor R6 (224, figure 8-6,
securing no. 3 shroud (191) to fan mount-
sheet 5) as follows:
ing bracket (196). Remove no. 3 shroud.
(a) Removal.
Remove screw (190), washer (192), cen-
6.
tering washer (208), mica washer (207),
1. Remove 20 screws (49, figure 8-6, sheet 1)
mica washer (205), and centering washer
and washers (50) securing PSTS front
|
|
Privacy Statement - Press Release - Copyright Information. - Contact Us |
Click
here for thousands of PDF manuals