Quantcast Chapter 3. OPERATION

 

Click here to make tpub.com your Home Page

Page Title: Chapter 3. OPERATION
Back | Up | Next

Click here for thousands of PDF manuals

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
Chapter 2. SERVICE UPON RECEIPT OF EQUIPMENT - TM-11-6625-2478-120014
Up
TM-11-6625-2478-12 Test Set Control Monitor - Recording Head AN/AYM-9 Manual
Next
Table 3-1. Simulator, Monitor Input SM-627/A YM-9, Controls, Indictors and Connectors (fig -1)
TM 11-6625-2478-12
CHAPTER 3
OPERATION
Section I. OPERATOR'S CONTROLS AND INDICATORS
3-1. Introduction
controls, indicators, connectors, and test points of Test
Set, Control Monitor-Recording Head AN/AYM-9. Figure
This section illustrates and describes the function of
3-1 illustrates and locates the controls, indicators,
controls, indicators, connectors, and test points of Test
connectors, and test points on Simulator, Monitor Input
Set, Control Monitor-Recording Head AN/ AYM-9.
SM-627/AYM-9.
The  function  of  controls  and
3-2. Operator's Controls, Indicators,
connectors  on  Case,  Test  Set  CY-7117/AYM-9,
Connectors, and Test Points
including Polaroid Camera CU-5, are given in table 3-2
and illustrated in figures 3-2 and 3-10.
Tables 3-1 and 3-2 identify and describe the function of
Table 3-1. Simulator, Monitor Input SM-627/A YM-9,
Controls, Indicators and Connectors (fig. 3-1)
Control, indicator or connector
Function
BCD+3 indicator lamps ................................................................................................... Light to indicate presence of binary coded decimal (+3) readout which
corresponds to various positions of Control-Monitor C-8338/
AYA-10 thumbwheel switches. Lamp indications are as follows:
Lamp
BCD + 3 bit
0
1
2
2
2
2
4
2
3
8
2
BCD + 3--PRESS TO TEST switch (pushbutton switch) .............................................. When pressed, lights BCD+ indicator lamps first purposes.
DECIMAL indicator lamps ............................................................................................... Lighted lamp indicates presence of decimal number which cor-
responds to selected positions of Control-Monitor C-8338/AYA-
10 thumbwheel switches.
DECIMAL-PRESS TO TEST switch (pushbutton switch)
When pressed, lights DECIMAL indicator lamps for test purposes.
BCD indicator lamps ....................................................................................................... Light to indicator presence of binary coded decimal readout which
corresponds to various positions of Control-Monitor C-8338/
AYA-10 thumbwheel switches. Lamp indications are as follows:
Lamp
BCD bit
0
1
2
1
2
2
2
4
2
BCD-PRESS TO TEST switch (pushbutton switch)
When pressed, lights BCD, BATTERY INDICATOR, SINGLE
PULSE INDICATOR, 6.3VAC, GO, +5V, and FAILURE indi-
cator lamps for test purposes
BATTERY INDICATOR lamp ......................................................................................... When BATTERY TEST switch is pressed, lights to indicate cor-
rect Control-Monitor C-8338/AYA-10 battery voltage.
When pressed, checks Control-Monitor C-8338/AYA-10 battery
BATTERY TEST switch (pushbutton switch)
voltage
-522VDC indicator lamp .................................................................................................. Lights to indicate presence of -522 volts dc output
+ 500VDC indicator lamp ................................................................................................ Light to indicate presence of + 500 volts dc output.
-80VDC indicator lamp.................................................................................................... Lights to indicate presence of -80 volts dc output.
+HORIZ test point ........................................................................................................... Provides means of monitoring + horizontal deflection signal.
-HORIZ test point ............................................................................................................ Provides means of monitoring -horizontal deflection signal.
+ VERT test point............................................................................................................ Provides means of monitoring + vertical deflection signal.
VERT test point ............................................................................................................... Provides means of monitoring -vertical deflection signal.
UNBLANKING test point ................................................................................................. Provides means monitoring unblanking signal.
3-1

Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc.