Order this information in Print

Order this information on CD-ROM

Download in PDF Format

     

Click here to make tpub.com your Home Page

Page Title: Table 4-10. Troubleshooting Engine Oil Temp NO 1 or NO 2 (AVIM)
Back | Up | Next

Click here for a printable version

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Combat
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
USMC
   
Products
  Educational CD-ROM's
Printed Manuals
Downloadable Books
   

 

TM 55-4920-412-13&P g.  Engine Oil Temp NO 1 and NO 2. (1) Connect   Digital   multimeter   to   connector   NO  1 pin g (HI)and h (LOW), using two leads. (2) Set ENGINE  OIL  TEMP  NO  1  CAL/NOR  switch to CAL, HI/LO switch to HI and variable control fully CW. NOTE Measure  resistance  of  test  leads  and subtract from resistance indications (3) Measure    resistance.        Digital    multimeter    will indicate between 150.2 and 151.0 ohms.  If not, perform Troubleshooting Table 4-10. (4) Set  ENGINE  OIL  TEMP  NO  1  HI/LO  switch  to LO.    Digital  multimeter  will  indicate  between  75.3  and 75.9 ohms.  If not, perform Troubleshooting Table 4-10. (5) Set  ENGINE  OIL  TEMP  NO  1  CAL/NOR  switch to  NOR.    Digital  multimeter  shall  indicate  between  170 and 190 ohms plus calibrated resistance. (6) Adjust   variable   control   from   fully   CW   to   fully CCW.    Digital  multimeter  will  indicate  between  73.6  and 77.6 ohms.  If not, perform Troubleshooting Table 4-10. (7) Disconnect  leads  from  connector  NO  1  pins    g (HI) and h (LOW) and connect to connector NO 2 pins  g (HI) and h (LOW). (8) Repeat    (2)    through    (6)    above,    except    use ENGINE OIL TEMP NO 2 controls. Table 4-10.  Troubleshooting Engine Oil Temp NO 1 or NO 2 (AVIM) NOTE Before performing troubleshooting, remove DC simulator A4 board and reconnect using extender board. Trouble Probable Cause Remedy No HI-CAL resistance Eng Oil Temp NO 1 Replace defective components, (S20) (S21) (R41) Figures 4-6, 4-7, FO-2, FO-5 or replace Eng Oil Temp NO 2 A4 board. (S22) (S23) (R38) HI-CAL Resistance Trim resistors Use decade resistor box, and check or Indication out of tolerance NO 1 - (R42) replace defective components, NO 2 - (R39) Figures 4-6, 4-7, FO-2, FO-5 or replace A4 board. HI-CAL resistance NO 1 - (R41) (R43) Replace defective components, Indication out of tolerance (S20) or (S21) Figures 4-6, 4-7, FO-2, FO-5 or replace resistors checked or replaced (R42) or NO 2 - (R38) (R40) A4 board. (R39) (S22) (S23) LO-CAL resistance NO 1 - (S20) Replace defective components, Indication out of tolerance NO 2 - (S22) Figures 4-6, 4-7, FO-2, FO-5 or replace A4 board. NOR-FULLY CCW NO 1 - (R9) Replace defective components, Resistance out of tolerance NO 2 - (R10) Figures 4-6, 4-7, FO-2, FO-5 or replace A4 board. NOR-FULLY CW NO 1 - (R9) Replace defective components, Resistance out of tolerance NO 2 - (R10) Figures 4-6, 4-7, FO-2, FO-5 or replace A4 board. NOTE Not  all  components  listed  for  circuits  above  are  indicated  in  Table.    Refer  to applicable circuits and Troubleshoot using information provided in Table. NOTE Resistance checks are also listed on figure 4-7. Change 2  4-15

Privacy Statement - Press Release - Copyright Information. - Contact Us - Support Integrated Publishing

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business