Stopping Procedure - TM-11-6625-2478-120027

TM 11-6625-2478-12

(20) On SM-627/AYM-9, set ON-OFF switch to OFF.

t 0.10 inch in diameter (fig. 3-6).

(16) Remove camera cover assembly from access

(21) Loosen 10 captive fastener studs securing he

opening of Polaroid Camera CU-5 and slide cover

welded plate assembly cover and remove cover.

(22) Loosen captive fastener stud securing clamp

assembly along cable release to gain access to the

shutter speed and lens opening levers.

assembly C and remove IR RHA from the clamp

(17) Set camera shutter speed for a 1/15 second

assembly.

exposure time and set the lens opening to f/5.6 (para 3-

(23) Disconnect connector P2 of cable CX-12727 'U,

8b(3)).

removing the IR RHA.

(18) Slide the camera cover assembly along the

(24) Close clamp assembly C and secure with raptive

cable release and press camera cover assembly into

fastener stud.

(25) Rotate turntable assembly for maximum access

access opening of Polaroid Camera CU-5 to exclude

extraneous light.

to connector J1 (fig. 3-11).

(19) On SM427/AYM-9, set RHA TEST SELECT

(26) Disconnect connector P1 of cable CX-12727 /U

switch to PHOSPHOR.

from connector J1 on the internal sic of CY-

(20) Depress camera cable release.

7117/AYM-9.

(21) Develop exposed film (para 3-8b(4)). The

f Recorder, Code Matrix Block LA-4A Test Procedures.

(1) Connect connector P1 of Cable Assembly,

resulting print shall show a raster (fig. 3-7).

(22) On SM-627/AYM-9, set ON-OFF switch to

Special Purpose, Electrical CX-12726/U to the internal

OFF.

sic of connector J1 on the CY-7117/AYM-9. Connect

(23) Loosen 10 captive fastener studs securing

connector P2 t the connector on LA434A (fig. 3-11).

(2) Rotate turntable of KE-59A until spring-

the welded plate assembly cover and remove cover.

(24) Loosen captive fastener stud securing clamp

loaded locator pin locks into position B. (3)

Place

assembly B and remove LA434A from the clamp

LA434A on clamp assembly B and rotate the LA-434A

assembly.

until captive fastener on the body of LA-434A is in the

(25) Disconnect connector P2 of cable CX-

down position and in the space provided on clamp

assembly B.

12726/U, removing the LA434A.

(4) Position LA434A such that the front face is in line

(26) Close clamp assembly B and secure with

(5)

and parallel with the lens of the camera.

captive fastener stud.

(27) Rotate turntable assembly for maximum

Secure clamp assembly B by means of cap- tive

fastener stud.

access to connector J1 (fig. 3-11).

(6) Mount welded plate assembly cover on top of the

(28) Disconnect connector P1 of cable CX-

welded plate and secure with 10 captive fastener studs.

12726/U from connector J1 on the internal sic of

(7) On SM-627/AYM-9, set RHA TEST SELECT

CY-7117/AYM-9.

3-9. Stopping Procedure

switch to KA76.

(8) On SM4-627/AYM-9, set ON-OFF switch to

To stop operation of Test Set, Control Monitor-

ON.

Recording Head AN/AYM-9, proceed as follows:

(9) Remove camera cover assembly from access

a. Set ON-OFF switch to OFF (fig. 3-1).

b. Disconnect P2 of Cable Assembly, Power, Elec-

opening of Polaroid Camera CU-5 and slide cover

assembly along cable release to gain access to the

trical, CX-12723/AYM-9 from 115 volts, 400 Hz power

shutter speed and lens opening levers.

source (fig. 3-3). Disconnect P1 of Cable Assembly,

(10) Set camera shutter speed to T and set lens

Power, Electrical, CX-12723/AYM-9 from connector J4

opening to f/5.6 (para 3-8b(3)).

on Simulator, Monitor Input SM-627/AYM-9.

(11) Slide camera cover assembly along cable

c. Disconnect P1 of Cable Assembly, Special Pur-

release and press camera cover assembly into access

pose, Electrical CX-12725/U from connector J3 on

opening of Polaroid Camera CU-5 to exclude ex-

Simulator, Monitor Input SM-627/AYM-9. Disconnect P2

traneous light.

of Cable Assembly, Special Purpose, Electrical CX-

(12) Depress camera cable release.

12725/U from connector J1 on Case, Test

(13) On SM-627/AYM-5, depress SINGLE PULSE

Set CY-7117/AYM-9.

d. To secure Test Set, Control Monitor-Recording

pushbutton. The SINGLE PULSE INDICATOR lamp

Head AN/AYM-9 after use, proceed as follows:

shall flash.

(1) Disconnect all cable assemblies from Test

(14) Depress camera cable release.

(15) Develop exposed film (para -8(4)). The

resulting print shall show a circle of small dots 0.35

3-13