Table 3-1. Simulator, Monitor Input SM-627/A YM-9, Controls, Indictors and Connectors (fig -1) (cont)

TM 11-6625-2478-12

Table 3-1. Simulator, Monitor lnput SM-627/AYM-9,

Controls, Indicators and Connectors (fig. 3 -1) - Continued

Control, indicator or connector Function

DECIMAL THUMBWHEEL SWITCH TEST switch ....................................................... Provides test of Control-Monitor C-8338/AYA-10 thumbwheel

(12-position rotary switch)

switches corresponding to selected switch position. In OFF

position, disconnects Control-Monitor C-8338/AYA-10 thumb-

wheel switches In ENABLE position, actiates DECIMAL

THUMBWHEEL AND PANEL SWITCH TEST

switch.

DECIMAL THUMBWHEEL AND PANEL SWITCH TEST ............................................ Provides test of Control-Monitor C-8338/AYA-10 thumbwheel

(12-position rotary switch of which 10 positions are used)

switches and POWER switch corresponding to selected

switch position In OFF position, disconnects Control-Monitor

C-8338/AYA-10 switches.

115VDC indicator lamp .................................................................................................. Lighs to indicate that 115 volts dc power supply is operational

6.3VAC indicator lamp..................................................................................................... Lights to indicate that 6.3 volts ac power supply is operational

115VAC indicator lamp.................................................................................................... Lights to indicate that 115 volts ac, 400 Hz has been applied

GO indicator lamp ........................................................................................................... Lights to indicate that voltages within Simulator, Monitor

Iput SM-627/AYM-9 are operational.

+5V indicator lamp........................................................................................................... Lights to indicate that + 5 volts dc power supply is operational.

FAILURE indicator lamp.................................................................................................. Lights o indicate that one or more operating voltages within

Simulator, Monitor Input SM-6i/AYM-9 are absent.

+5V testpoint.. ................................................................................................................. Provides means of monitoring +5 o!ts deoutput

+ 10V test point ............................................................................................................... Provides means of monitoring + 10 olts deoutput

+ 15V test point ............................................................................................................... Provides means of monitoring + 15 voltsdeoutput

-15V stesint point ............................................................................................................ Provides means of monitoring-15 volts deoutput.

+ 25V test point ............................................................................................................... Provides means of monitoring +25 volts deoutput

-25V tst point ................................................................................................................... Provides means of monitoring --25 volts dc output.

+ 85V st point ................................................................................................................. Provides means of monitoring +85 volts deoutput.

+ 115V tst point ............................................................................................................... Provides means of monitoring + 115 volts dc output.

GND test point................................................................................................................. Provides means of conneting test equipment to internal ground.

ELAPSED TIME meter.................................................................................................... Provides indication of total hours of operation of Simulator,

Monitor Input SM-627/AYM-9.

ON-OFF switch (2-position toggle switch) ...................................................................... In ON position, connecs primary power to Simulator, Monitor

Input SM-627/AYM-9. In OFF position, disconnects primary

power.

EXT GND terminal .......................................................................................................... Proides for connection of external ground to Simulator,

Monitor Input SM427/AYM-9 chassis

CONTROL DISPLAY MONITOR:

Connector J1................................................................................................................... Provides means of connecting Simulator, Monitor Input SM-

627/AYM-9 to Control-Monitor C-8338/AYA-10.

Connector J2................................................................................................................... Provides means of connecting Simulator, Monitor Input

SM627/AYM-9 to Control-Monitor C-8338/AYA-10.

RECORDING HEAD ConnetorJ3 ................................................................................... Provides means of connecting Smulator, Monitor Input

SM-627/AYM-9 to Control Monitor C-8338/AYA-10 or Camera,

Still Picture KE-59A.

POWER Connector J4.................................................................................................... Provides means of connecting Simulator, Monitor Input

SM627/AYM-9 115 volts ac, 400 Hz power source.

Table 3-2. Case Test Set CY-7117/AYM-9, Connector (fig. 3-2)

Connector

Function

Connector J1................................................................................................................... Provides means of connecting Camera, Still Picture KE-9A

to Simulator, Monitor Input SM-627/AYM-9 Also provides

means of connecting recording head assembly or monitor

assembly under test to Camera, Still Picture KE-59A.

Table 3-3. Polaroid Camera CU-5 Controls and Indicators (fig 3-10)

Control or indicator

Function

Shutter speed lever.......................................................................................................... Provides for setting speed of shutter operation.

Red mark......................................................................................................................... Points shutter speed setting on setting indicator.

Lens opening lever .......................................................................................................... Provides for setting lens diaphragm to desired opening.

Lens opening pointer ....................................................................................................... Points to lens opening setting on setting indicator.

Setting indicator............................................................................................................... Indicates shutter speed and lens opening setting.

Cable release socket ....................................................................................................... Provides for connecting able release to shutter mechanism.

Exposure door control (fig. 3-2) ...................................................................................... In OPEN position, prevents image from being projected on

film. In LOCK position, permits image to be projected on film.

3-3