How to Locate Repair Parts - TM-11-5895-1097-40P0004

TM 11-5895-1097-40P

are assigned to support items to indicate the disposition

TM 11-5895-1097-12, Test Set, Crystal Module TS-

action on unserviceable items. The recoverability code is

3630/GRA-114

entered in the fifth position of the Uniform SMR Code

TM 11-5895-1097-20P, Test Set, Crystal Module TS-

format as follows:

3630/GRA-114 (To be published)

Recoverability

TM 11-5895-1097-40, Test Set, Crystal Module TS-

codes

Definition

3630/GRA-114 (To be published)

b. National stock numbers (NSN's) that are missing

Z - Nonreparable item. When unserviceable, condemn

from P source coded items have been applied for and

and dispose at the level indicated in position 3.

will be added to this TM by future change/revision when

H - Reparable item. When uneconomically reparable,

they are entered in the Army Master Data File (AMDF).

condemn and dispose at the general support level.

Until the NSN's are established and published, submit

c. National Stock Number. Indicates the National

exception requisitions to: Commander, US Army

stock number assigned to the item and will be used for

Communications-Electronics Command and

Fort

requisitioning purposes.

Monmouth, ATTN: DRSEL-MM, Fort Monmouth, New

d. Federal Supply Code for Manufacturer (FSCM).

Jersey 07703 for the part required to support your

The FSCM is a 5-digit numeric code listed in SB 708-

equipment.

41/42 which is used to identify the manufacturer,

distributor, or Government agency, etc.

e. Part Number. Indicates the primary number

How to Locate Repair Parts

a. When National stock number or part is unknown.

used by the manufacturer (individual, company, firm,

(1) First.

Using the table of contents,

corporation, or Government activity), which controls the

determine the functional group within which the item

design and characteristics of the item by means of its

belongs.

This is necessary since illustrations are

engineering drawings, specifications, standards, and

prepared for functional groups and listings are divided

inspection requirements to identify an item or range of

into the same groups.

items.

(2) Second. Find the illustration covering the

NOTE

functional group to which the item belongs.

When a stock numbered item is

(3) Third. Identify the item on the illustration

requisitioned, the repair part received

and note the illustration figure and item number of the

may have a different part number

item.

than the part being replaced.

(4) Fourth. Using the Repair Parts Listing,

f. Description. Indicates the Federal item name

find the figure and item number noted on the illustration.

and, if required, a minimum description to identify the

b. When National stock number or part number is

item.

known.

g. Unit of Measure (U/M). Indicates the standard of

(1) First. Using the Index of National Stock

the basic quantity of the listed item as used in performing

Numbers and Part Numbers, find the pertinent National

the actual maintenance function. This measure is

stock number or part number. This index is in NIIN

expressed by a two-character alphabetical abbreviation

sequence followed by a list of part numbers in

(e.g., ea, in, pr, etc). When the unit of measure differs

alphameric sequence, cross-referenced to the illustration

from the unit of issue, the lowest unit of issue that will

figure number and item number.

satisfy the required units of measure will be

(2) Second. After finding the figure and item

requisitioned.

number, locate the figure and item number in the repair

h. Quantity Incorporated in Unit. Indicates the

parts list.

quantity of the item used in the breakout shown on the

illustration figure, which is prepared for a functional

Abbreviations

group, subfunctional group, or an assembly.

Not applicable.

Special Information

The following publications pertain to the TS-

3630/GRA-114 and is components:

(Next printed page is 4)