|
|
TM 11-4920-294-40P-1
SECTION I
INTRODUCTION
authorized to USE and REPAIR support items. The
1. Scope
maintenance codes are entered in the third and fourth
This manual lists spares and repair parts; special tools;
positions of the Uniform SMR Code format as follows:
special test, measurement, and diagnostic equipment
(a) The maintenance code entered in
(TMDE), and other special support equipment required
the third position will indicate the lowest maintenance
for performance of general support maintenance of the
level authorized to remove, replace, and use the support
AN/ASM-417. It authorizes the requisitioning and issue
item. The maintenance code entered in the third position
of spares and repair parts as indicated by the source and
will indicate one of the following levels of maintenance:
maintenance codes.
Code
Application/Explanation
2. General
O
-Support item is removed, replaced, used at the
This Repair Parts and Special Tools List is divided into
organizational level.
the following sections:
H
-Support item is removed, replaced, used at the
a. Section II. Repair Parts List. A list of spares
general support level.
and repair parts authorized for use in the performance of
(b) The maintenance code entered in
maintenance. The list also includes parts which must be
the fourth position indicates whether the item is to be
removed for replacement of the authorized parts. Parts
repaired and identifies the lowest maintenance level with
lists are composed of functional groups in numeric se-
the capability to perform complete repair (i.e., all
quence, with the parts in each group listed in figure and
authorized mainte-nance functions). This position will
item number sequence.
contain one of the following maintenance codes:
b. Section III. Special Tools List. Not applicable.
Code
Application/Explanation
c. Section IV. National Stock Number and Part
H
-The lowest maintenance level capable of
Number Index. A list, in National item identification
complete repair of the support item is the
number (NIIN) sequence, of all National stock numbers
general support level.
(NSN) appearing in the listings, followed by a list, in
Z
-Nonreparable. No repair is authorized.
alphameric sequence, of all part numbers appearing in
(3) Recoverability code. Recoverability codes
the listings. National stock numbers and part numbers
are assigned to support items to indicate the disposition
are cross-referenced to each illustration figure and item
action on unserviceable items. The recoverability code is
number appearance.
entered in the fifth position of the Uniform SMR Code
3. Explanation of Columns
format as follows:
a. Illustration. This column is divided as follows:
Recoverability
(1) Figure number.
Indicates the figure
codes
Definition
number of the illustration on which the item is shown.
Z
-Nonreparable item.
When unserviceable,
(2) Item number. The number used to identify
condemn and dispose at the level indicated in
item called out in the illustration.
position 3.
b. Source, Maintenance, and Recoverability (SMR)
H
-Reparable item.
When uneconomically
Codes.
reparable, condemn and dispose at the general
(1) Source code. Source codes indicate the
support level.
manner of acquiring support items for maintenance,
D
-Reparable item. When beyond lower level
repair, or overhaul of end items. Source codes are
repair capability, return to depot. Condemnation
entered in the first and second positions of the Uniform
and disposal not authorized below depot level.
SMR Code for-mat as follows:
A
-Item requires special handling or condemnation
Code
Definition
procedures because of specific reasons (i.e.,
PA -
Item procured and stocked for anticipated or
precious metal content, high dollar value, critical
known usage.
material or hazardous material).
Refer to
XD-
A support item that is not stocked. When
appropriate manuals/directives for specific
required, item will be procured through
instructions.
normal supply channels.
c. National Stock Number. Indicates the National
NOTE
stock number assigned to the item and will be used for
Cannibalization or salvage may be used
requisitioning purposes.
as a source of supply for any items
d. Part Number. Indicates the primary number
source coded above except those coded
used by the manufacturer ('individual, company, firm,
XA and aircraft sup-port items as
corpora-tion, or Government activity), which controls the
restricted by AR 700-42.
design
(2) Maintenance code. Maintenance codes
are assigned to indicate the levels of maintenance
1
|
Privacy Statement - Press Release - Copyright Information. - Contact Us |