Recoverability code - TM-11-6625-2781-24P-40005

TM 11-6625-2781-24P-4

(3) Recoverability code. Recoverability codes

the illustration figure, which is prepared for a functional

group, subfunctional group, or an assembly.

are assigned to support items to indicate the disposition

action on unserviceable items. The recoverability code is

entered in the fifth position of the Uniform SMR Code

Special Information

format as follows:

a. The following publications pertain to the PL-

1400/U and its components

Recoverability:

codes

Definition

TM 11-6625-2781-14-4, Plug-In Unit, Electronic Test

Z-

Nonreparable item. When unserviceable,

Equipment PL-1400/U (Hewlett-Packard Model

condemn and dispose at the level indicated

8555A)

in position 3.

TM11-6625-2781-14&P Spectrum Analyzer IP-12161GR

H-

Reparable

item. When uneconomically

(Hewlett-Packard Model 141T)

reparable, condemn and dispose at the

b. National stock numbers (NSN's) that are

general support level.

missing from P source coded items have been applied

D-

Reparable item. When beyond lower level repair

for and will be added to this TM by future change/revision

capability, return to depot. Condemnation

when they are entered in the Army Master Data File

and disposal not authorized below depot

(AMDF). Until the NSN's are established and published,

level.

submit exception requisitions to Commander, US Army

L-

Reparable item. Repair, condemnation, and

Communications-Electronics Command, ATTN: DR-

disposal

not

authorized

below

SEL-MM, Fort Monmouth, NJ 07703 for the part

depot/specialized repair activity level.

required to support your equipment.

c. National Stock Number.

Indicates the

How to Locate Repair Parts

National -stock number assigned to the item and will be

a. When National stock number or part

used for requisitioning purposes

number is unknown.

Federal Supply Code for Manufacturer

(1) First. Using the table of contents,

FSCM). The FSCM is a 5-digit numeric code listed in SB

determine the functional group within which the item

708-41/42 which is used to identify the manufacturer,

belongs.

This is necessary since illustrations are

distributor, or Government agency, etc.

prepared for functional groups and listings are divided

into the same groups.

e. Part Number. Indicates the primary number

(2) Second. Find the illustration covering

used by the manufacturer (individual, company, firm,

the functional group to which the item belongs.

corporation, or Government activity), which controls the

(3) Third.

Identify the item on the

design and characteristics of the item by means of its

illustration and note the illustration figure and item

engineering drawings, specifications, standards, and

number of the item.

inspection requirements to identify an item or range of

(4) Fourth. Using the Repair Parts Listing,

items.

find the figure and item number noted on the illustration.

b. When National stock number or part

NOTE

number is known.

When a stock numbered, item is requisitioned,

(1) First. Using the Index of National Stock

the repair part received may have a different part

Numbers and Part Numbers, find the pertinent National

number than the part being replaced.

stock number or part number. This index is in NIIN

sequence followed by a list of part numbers in

Description. Indicates the Federal item

alphameric

sequence,

cross-referenced

the

name and, if required, a minimum description to identify

illustration figure number and item number.

the item.

(2) Second. After finding the figure and

g. Unit of Measure (U/M).

Indicates the

item number, locate the figure and item number in the

standard of the basic quantity of the listed item as used

repair parts list.

in performing the actual maintenance function. This

measure is expressed by a two-character alphabetical

Abbreviations

abbreviation (e.g., ea, in, pr, etc). When the unit of

Not applicable.

measure differs from the unit of issue, the lowest unit of

issue that will satisfy the required units of measure will

be requisitioned.

h. Quantity Incorporated in Unit. Indicates the

quantity of the item used in the breakout shown on