Quantcast TABLE NO. 3-32. SAS SYSTEM AIRSPEED SWITCH ,60 KNOTS Indicator Does Not Go On When LATL ACCLRM Control Is Set Above 1.3 Vdc And Does Not Go Off When LATL ACCLRM Control Is Set Below 1.0 Vdc

 

Click here to make tpub.com your Home Page

Page Title: TABLE NO. 3-32. SAS SYSTEM AIRSPEED SWITCH ,60 KNOTS Indicator Does Not Go On When LATL ACCLRM Control Is Set Above 1.3 Vdc A...
Back | Up | Next

Click here for thousands of PDF manuals

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
Table 3-31. INDICATORS NO. 2 AS SW ,60 KNOTS Does Not Go On When POWER +15 VDC Is Applied To TEST POINTS NO. 2 AS SW.
Up
TM-1-6625-735-14 Test Set Stabilization System P/N 70700-20650-050 Manual
Next
TABLE NO. 3-34. Multimeter No. 1 Does Not Indicate 12.0 6 0.5 Vdc And Multimeter No. 2 Does Not Indicate 12.0 6 0.7 Vdc When AS SENSOR Switch Is Placed To SIM STAB 1&2.
TM 1-6625-735-14
TABLE NO. 3-32. SAS SYSTEM AIRSPEED SWITCH ,60 KNOTS Indicator Does Not Go On When
LATL ACCLRM Control Is Set Above 1.3 Vdc And Does Not Go Off When LATL ACCLRM Control Is
Set Below 1.0 Vdc. (Cont)
TEST OR INSPECTION
CORRECTIVE ACTION
3. Place SAS SYSTEM AIRSPEED SWITCH to NORM. Go to 4.
4. Place LATL ACCLRM control to SIM SAS 1. Go to 5.
5. Turn LATL ACCLRM control counterclockwise (L) and clockwise (R) to vary
multimeter indicator 1.0 6 1.0 vdc. SAS AIRSPEED SWITCH ,60 KNOTS indicator
lamp shall light between 1.4 6 0.1 vdc and shall remain on above this voltage range;
also, SAS AIRSPEED SWITCH ,60 KNOTS indicator shall go off 1.1 6 0.1 vdc and
shall remain off below this voltage range.
Step 1. If multimeter indicates 0.0 vdc, go to 6.
Step 2. If multimeter indication is not correct, replace component board assembly A3.
6. Check switch S23 for continuity.
Step 1. If continuity exists, replace circuit board assembly A2.
Step 2. If continuity does not exist, replace switch S23.
TABLE NO. 3-33. SAS SYSTEM AIRSPEED SWITCH >60 KNOTS Indicator Does Not Go On When
LATL ACCLRM Control Is Fully Clockwise And SAS SYSTEM AIRSPEED SWITCH ,60 KNOTS
Does Not Go On When LATL ACCLRM Control Is Fully Counterclockwise.
TEST OR INSPECTION
CORRECTIVE ACTION
NOTE
Test lamps for condition before continuing.
During the following steps, note the status
(on or off) of all lamps.
1. Place SAS SYSTEM AIRSPEED SWITCH TO >60 KNOTS. Go to 2.
2. Turn LATL ACCLRM control fully clockwise (R). SAS SYSTEM AIRSPEED ,60
KNOTS indicator lamp shall go on.
Step 1. If indicator lamp does not go on, replace switch S23.
Step 2. If indicator lamp goes on, go to 3.
3-29

Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc.